3 files changed, 9 insertions, 82 deletions
diff --git a/keyboards/40percentclub/nein/config.h b/keyboards/40percentclub/nein/config.h
index 5c45f213ca..c30966d9d2 100644
--- a/keyboards/40percentclub/nein/config.h
+++ b/keyboards/40percentclub/nein/config.h
@@ -16,83 +16,11 @@
 
 #pragma once
 
-#include "config_common.h"
-
-/* key matrix size */
-#define MATRIX_ROWS 3
-#define MATRIX_COLS 3
-
-/* Keyboard Matrix Assignments */
-#define DIRECT_PINS { \
-    { F4, F5, F6 }, \
-    { F7, B1, B3 }, \
-    { B2, B6, B5 }  \
-}
-
-/*
- * Split Keyboard specific options, make sure you have 'SPLIT_KEYBOARD = yes' in your rules.mk, and define SOFT_SERIAL_PIN.
- */
-// #define SOFT_SERIAL_PIN D0 // or D1, D2, D3, E6
-
-// #define BACKLIGHT_PIN B7
-// #define BACKLIGHT_BREATHING
-// #define BACKLIGHT_LEVELS 3
-
-// #define RGB_DI_PIN E2
-// #ifdef RGB_DI_PIN
-//   #define RGBLED_NUM 16
-//   #define RGBLIGHT_HUE_STEP 8
-//   #define RGBLIGHT_SAT_STEP 8
-//   #define RGBLIGHT_VAL_STEP 8
-//   #define RGBLIGHT_LIMIT_VAL 255 /* The maximum brightness level */
-//   #define RGBLIGHT_SLEEP  /* If defined, the RGB lighting will be switched off when the host goes to sleep */
-// /*== customize breathing effect ==*/
-//   /*==== (DEFAULT) use fixed table instead of exp() and sin() ====*/
-//   #define RGBLIGHT_BREATHE_TABLE_SIZE 256      // 256(default) or 128 or 64
-//   /*==== use exp() and sin() ====*/
-//   #define RGBLIGHT_EFFECT_BREATHE_CENTER 1.85  // 1 to 2.7
-//   #define RGBLIGHT_EFFECT_BREATHE_MAX    255   // 0 to 255
-// #endif
-
-/* Debounce reduces chatter (unintended double-presses) - set 0 if debouncing is not needed */
-#define DEBOUNCE 5
-
-/* define if matrix has ghost (lacks anti-ghosting diodes) */
-//#define MATRIX_HAS_GHOST
-
-/* number of backlight levels */
-
 /* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */
 #define LOCKING_SUPPORT_ENABLE
 /* Locking resynchronize hack */
 #define LOCKING_RESYNC_ENABLE
 
-/* If defined, GRAVE_ESC will always act as ESC when CTRL is held.
- * This is userful for the Windows task manager shortcut (ctrl+shift+esc).
- */
-// #define GRAVE_ESC_CTRL_OVERRIDE
-
-/*
- * Force NKRO
- *
- * Force NKRO (nKey Rollover) to be enabled by default, regardless of the saved
- * state in the bootmagic EEPROM settings. (Note that NKRO must be enabled in the
- * makefile for this to work.)
- *
- * If forced on, NKRO can be disabled via magic key (default = LShift+RShift+N)
- * until the next keyboard reset.
- *
- * NKRO may prevent your keystrokes from being detected in the BIOS, but it is
- * fully operational during normal computer usage.
- *
- * For a less heavy-handed approach, enable NKRO via magic key (LShift+RShift+N)
- * or via bootmagic (hold SPACE+N while plugging in the keyboard). Once set by
- * bootmagic, NKRO mode will always be enabled until it is toggled again during a
- * power-up.
- *
- */
-//#define FORCE_NKRO
-
 /*
  * Feature disable options
  *  These options are also useful to firmware size reduction.
@@ -108,7 +36,3 @@
 //#define NO_ACTION_LAYER
 //#define NO_ACTION_TAPPING
 //#define NO_ACTION_ONESHOT
-
-/* Bootmagic Lite key configuration */
-// #define BOOTMAGIC_LITE_ROW 0
-// #define BOOTMAGIC_LITE_COLUMN 0
diff --git a/keyboards/40percentclub/nein/info.json b/keyboards/40percentclub/nein/info.json
index 09d25e30de..ba39cb834d 100644
--- a/keyboards/40percentclub/nein/info.json
+++ b/keyboards/40percentclub/nein/info.json
@@ -8,6 +8,15 @@
     "pid": "0x9999",
     "device_version": "99.9.9"
   },
+  "processor": "atmega32u4",
+  "bootloader": "caterina",
+  "matrix_pins": {
+    "direct": [
+      ["F4", "F5", "F6"],
+      ["F7", "B1", "B3"],
+      ["B2", "B6", "B5"]
+    ]
+  },
   "layouts": {
     "LAYOUT_ortho_3x3": {
       "layout": [
diff --git a/keyboards/40percentclub/nein/rules.mk b/keyboards/40percentclub/nein/rules.mk
index 7dae3a8423..3b6a1809db 100644
--- a/keyboards/40percentclub/nein/rules.mk
+++ b/keyboards/40percentclub/nein/rules.mk
@@ -1,9 +1,3 @@
-# MCU name
-MCU = atmega32u4
-
-# Bootloader selection
-BOOTLOADER = caterina
-
 # Build Options
 #   change yes to no to disable
 #